| |
|
|
| |
 Square Helical Cutterheads
FEATURES
- Greatly reduces noise level.
- Higher chip removal rate.
- Accurate helix angle assures superior cutting performance.
- Tungsten carbide inserts are staggered for finer surface finish.
- Cutterhead body is phosphoric acid treated to resist corrosion.
- Reduced torque and horsepower requirements.
- Suitable for economic 14 x 14 x 2.0 mm., inserts or 15 x 15 x 2.5 mm high strength inserts.
|
|
| PART NO. |
CUTTING
CIRCLE |
CUTTING
LENGTH |
BORE
DIAMETER |
TCT SLOTS |
|
BORE SIZE |
** |
| HAS100100**6T14 |
100 |
100 |
** |
6 |
|
1-1/4" |
32 |
| HAS100150**6T14 |
100 |
150 |
** |
6 |
|
35 mm |
35 |
| HAS125100**6T14 |
125 |
100 |
** |
6 |
|
1-1/2" |
38 |
| HAS125125**6T14 |
125 |
125 |
** |
6 |
|
40 mm |
40 |
| HAS125150**6T14 |
125 |
150 |
** |
6 |
|
1-13/16" |
46 |
| HAS125200**6T14 |
125 |
200 |
** |
6 |
|
50 mm |
50 |
| HAS125230**6T14 |
125 |
230 |
** |
6 |
|
2 1/8" |
54 |
| HAS125240**6T14 |
125 |
240 |
** |
6 |
|
60 mm |
60 |
| HAS140100**6T14 |
140 |
100 |
** |
6 |
|
65 mm |
65 |
| HAS140150**6T14 |
140 |
150 |
** |
6 |
|
|
|
| HAS140230**6T14 |
140 |
230 |
** |
6 |
|
|
|
| HAS160100**6T14 |
160 |
100 |
** |
6 |
|
|
|
| HAS160150**6T14 |
160 |
150 |
** |
6 |
|
|
|
| HAS160230**6T14 |
160 |
230 |
** |
6 |
|
|
|
|
 |
| |
 
Rabbeting
FEATURES
- For use on a spindle shaper.
- Inserts provided on cutter surface and both sides permit cutting and rabbeting.
- Two inserts on each side of the cutter.
- Aluminum alloy cutter body, dynamically balanced for extra smooth running.
- Accommodates 14 x 14 x 2.0 inserts.
|
|
| PART NO. |
CUTTING CIRCLE |
CUTTING LENGTH |
SLOTS |
| HAB10065**4T14 |
100 |
65 |
4 |
| HAB12530**4T14 |
125 |
30 |
4 |
| HAB12550**4T14 |
125 |
50 |
4 |
| HAB12560**4T14 |
125 |
60 |
4 |
|
|
|
|
|
FEATURES
- Suitable for PAA, PAB and PAD series cutterheads.
- H.S.S. knife material.
- Quick lock system knife.
- Knife can be surface ground to a minimum of 2.45 mm thickness.
- Knives are 14 mm wide x 2.55 mm think.
| Quick Lock Knife Specification |
|
|
|
|
Quick Lock System Instruction
 |
STEP 1
Loosen set screws by using a 3mm hexagonal wrench. |
| |
 |
STEP 2
Use the hexagonal wrench to gently tap down the gib, then you can take out the knives radially. |
| |
 |
STEP 3
To mount new knives or use the other edge of the knife, make sure the knife is properly engaged with the cavity on the cutterhead body. |
| |
 |
STEP 4
Tap down again the gib, then the gib will automatically precisely secure the knife in place. Finally, tighten all set screws. |
| |
|
|
|
